博文

Disassembly and Calibration of New Holland Main Hydraulic Power Systems

图片
Tere is an instruction show you guide on how to remove and calibrate primary hydraulic power system electro-hydraulic remote valve for New Holland T6030 tractor. Related Contents: New Holland Electronic Service Tools (CNH EST 9.7 9.6 8.6 engineering Level) CNH Kit Diagnostic Tool Procedures: Removal: 1 Steam clean remote control valve assembly prior to removal. Lower hydraulic links. Remove covers on remote valve couplers. Remove support for pneumatic trailer brake couplers (where fitted). 2 Disconnect harness from electronic draft control solenoids, remote valve solenoids (2) and pressure feed hose (1). NOTE: Identify the remote valve connectors to facilitate correct re-installation 3Disconnect the lift cylinder hydraulic hoses from the EDC slice (1) 4Using suitable lifting equipment support remote valve assembly, remove the three base securing bolts and lift valve stack from tractor   Calibration: NOTE: The calibration procedure is controlled by the electronic ma
发表评论
阅读全文

How to Free Download WinEEM4s JCB Service Tool

图片
  What is WinEEM4s JCB Service Tool ? WinEEM4s JCB Service Tool is an easy tool for the monitoring and adjustment software to Sisu Diesel electronic Control Unit.Programs can be used for EEM2,EEM3,EEM4 ECU. WinEEM4s JCB Service Tool Introduction： 1.1. Purpose This document is the troubleshoot information for the AGCO POWER EEM4 Electronic Engine Management system. The provided fault descriptions include information on the possible causes for the fault, on the influence on the engine operation and instructions to resolve the problem. 1.2. Scope The system reports detected faults by fault codes. These fault codes can be read over the CAN bus from the EEM4 controller using a WinEEM Service Tool. The fault codes may also be transmitted over the CAN bus to a vehicle’s instrument panel. Alternatively, the fault codes can be shown using blink codes on a diagnostic lamp. When a fault code is known, the enclosed documentation can be used to analyze the reason for the fault an
发表评论
阅读全文

Adjusting JCB's Shovel Return System Guide

图片
 The shovel reset system is designed to automatically tilt the shovel forward when the loader arms are raised, this prevents a heaped shovel from depositing its contents over the back of the shovel onto the bonnet or cab when the loader arms are raised. This instruction show you guide on how to adjust shovel reset system for JCB 3CX, 4CX, 214e, 214, 215, 217 & VARIANTS Backhoe Loader Related Contents: JCB Heavy Duty Truck Diagnostic Tool When the loader arms are raised the feed back link A causes the cam plate B to rotate anti-clockwise. The rotation of the cam plate pulls the cable C which selects the loader valve block shovel spool D to tip the shovel forwards. When either a cable or feedback link is changed or if the shovel reset system is not operating correctly carry out functional adjustment check. Fitting 1 Adjust the feedback link A to 2065mm (81.3in). After adjusting tighten the lock nuts. 2 Fit cam plate B with the single threaded hole at the top. 3 Fit feed back link A t
发表评论
阅读全文

JPRO Professional heavy duty truck scan tool Reviews

图片
  The JPRO Professional heavy-duty scanning tool is incredibly user friendly and will help you to detect the issue quickly and efficiently. In this useful guide, we intend to delve deep into this advanced tool and review its key features and its pros and cons. You’ll also find the answers to some commonly asked questions. Whether you’re a major service center or an independent repair shop, if you’re considering adding the Noregon JPRO professional to your repair kit, you’re sure to find this guide helpful. So without further ado, let’s take a look at this exceptional piece of vehicle diagnostic equipment. It is a simple yet most comprehensive and powerful diagnostic tool that is compatible with all models. Besides, JPRO Professional heavy duty truck scan tool provides complete and real-time diagnostic services. It is also uniquely designed to provide a repair solution for the diagnosed problem, and better yet, is equipped with bi-directional functionality. This scan to
发表评论
阅读全文

Xhorse VVDI2 Commander key programmer Technical Service

图片
  About functions: Regard VAG, if you want to open the 5th IMMO authorization, you need to open the 4th IMMO first. Because 5th is derivatived from 4th. For BMW: Only BMW OBD is opened. Then you can open CAS4 authorization. Component security function of VVDI 1, it will be valid after you open the authorization for pin,mac and CS reading authorization. For VVDI 2,you can directly use component security function. Go to special function. you will find the component security option for A4,A5,A6,A8,Q5,Q7,Allroad. Customer asked questions for VVDI2 : Q: I do have BMW X5 from 2013+ , it’s F15 with CAS4+ I guess and 5M48H, it has all keys lost. What equipment I should buy from you to make a new key. A: 1) For 5M48H, you need to use XPROG or VVDI pro to read the date 2) Use BMW MULTI TOOL or VVDI 2 do CAS4+, and use the data you read out to generate the key data to match programming and simultaneous car For second steps. If you choose BMW MULTI TOOL, you still need to buy th
发表评论
阅读全文

Which version of PTT Tech Tool to diagnose Volvo Bus B7R B9R B11R B12R?

  This blog here will answer you this question: Which PTT Premium Tech Tool can diagnose Volvo B7R B9R B11R B12R bus? And which tool to use? Check professional answer as below: Some guys tested that Volvo PTT 2.04.87 diagnose Volvo B11R and B12R buses OK. Is that true? Yes. To diagnose Volvo Bus B7R, B9R, B11R and B12R bus you can use Volvo PTT 2.04.87 and newly released Volvo PTT 2.5.75! (Technicians from Autonumen.com confirmed that) Volvo Tech Tool 2.05.75 What’s new? Special Login id and own Info Lasted Apci+ Update Volvo Trucks (Older electrical system, Vehicle electrical system ’98); Volvo Trucks (Version2, Version3 Parameter Programming); Volvo Trucks (Version4 FH4/FM4 Parameter Programming); Volvo Buses (Conventional, Multiplexed, Multiplexed V2, Multiplexed V3 [/b]); Volvo Construction Equipment Parameter Programming; Volvo Penta (Version2, Version3); Volvo OEM Component Customer (Version2, Version3); Mack Trucks (V-MAC I/II/III, ITC, IV, IV+) Parameter Progr
发表评论
阅读全文

Volvo 88890300 Vocom Interface PTT 1.12 Installation Instructions

图片
  Volvo 88890300 Vocom Interface PTT 1.12 Installation Instruction 1.Please Unzip the files PTT-v1.12.260 Open the folder after unzipping Select setup to start the installation，input123456 When the installation is complete, select NO. Unzip the files of VTT1.12-KG Open the vtt1.12-kg folder and run the software. Click 1, 2, 3, 4 2.Open the software as administrator Input ID M311331 Click on the picture to select and click OK Pop up the picture above and select OK to open the software.
发表评论
阅读全文