How to Repair JCB K0415 Oil Pressure Low Alarm Trouble

 

How to Repair JCB K0415 Oil Pressure Low Alarm Trouble

This instruction show you guide on how to repair JCB K0415 oil pressure low alarm trouble.More repair case for JCB,please refer to:JCB Trouble Repair
How-to-Repair-JCB-K0415-Oil-Pressure-Low-Alarm-Trouble-1

Related Content:

WinEEM4s JCB Service Tool Free Download

The measured oil pressure is below the alarm limit. The low oil pressure signal may be caused by the following reasons:

The engine oil level is too low.

The oil quality is poor.

The oil filter is clogged.

The oil grade is not correct.

The oil is too hot.

The oil is diluted by fuel.

The oil pressure control valve is not operating correctly.

The oil pump has excessive wearing.

The oil pressure sensor wiring is defective.

The oil pressure sensor is defective.

Reaction in EEM

The FC is stored and the oil pressure the warning lamp is activated. The engine will stop after 30 seconds. The CAN message indicates that a shutdown is pending.

Solution

Find the cause for the low oil pressure indication. Check and repair the possible mechanical problems according to the service instructions:

Check the oil level and the condition of the oil.

Check the oil filter.

Check the mechanical condition of the engine.

To check the electrical defects, check the oil pressure sensor, the sensor wiring and the controller input: First save the error log and then erase it. Restart the ECU after erasing the error log. If the fault occurs again during the next driving cycle, check the following paths:

Check the oil pressure sensor wiring, the connectors and the contact surfaces of the connector pins (possible oxidation).

Check the operation with another oil pressure sensor to see if The oil pressure sensor is defective.

评论

发表评论

此博客中的热门博文

John Deere Service Advisor 5.2.467 2019 Agriculture Equipment Division

A brand new version of John Deere Service Advisor 5.2 for AG equipment is an offline application, that use Internet Explorer browser to communicate with the user. JOHN DEERE SERVICE ADVISOR AG 5.2 SPANISH (ESPA?OL) 02/2018 version is also available. Please indicate the preferred language in the comment field during the checkout process. Important Notice. Installation and activation are possible only with remote assistance using Teamviewer. Unlike the previous version (John Deere Service Advisor 4.2) to work with the application you need: Internet Explorer 11 (The shell) Last version of Adobe PDF reader (you will be asked to download the last version before the installation process begin) Last version of Java runtime environment (you will be asked to download the last version before the installation process begin) John Deere Service Advisor 5.2 System requirements: – O.S.: Windows 7 Pro/Ultimate; Windows 8 Pro, Windows 8.1 Pro, Windows 10 Home/Pro – CPU: Any CPU for W
阅读全文

Adjusting JCB's Shovel Return System Guide

图片
 The shovel reset system is designed to automatically tilt the shovel forward when the loader arms are raised, this prevents a heaped shovel from depositing its contents over the back of the shovel onto the bonnet or cab when the loader arms are raised. This instruction show you guide on how to adjust shovel reset system for JCB 3CX, 4CX, 214e, 214, 215, 217 & VARIANTS Backhoe Loader Related Contents: JCB Heavy Duty Truck Diagnostic Tool When the loader arms are raised the feed back link A causes the cam plate B to rotate anti-clockwise. The rotation of the cam plate pulls the cable C which selects the loader valve block shovel spool D to tip the shovel forwards. When either a cable or feedback link is changed or if the shovel reset system is not operating correctly carry out functional adjustment check. Fitting 1 Adjust the feedback link A to 2065mm (81.3in). After adjusting tighten the lock nuts. 2 Fit cam plate B with the single threaded hole at the top. 3 Fit feed back link A t
阅读全文

How to change speed limit using PLD file editor for John Deere Service Advisor EDL V2?

图片
  Please select the correct version which you need before make the order 1. With John Deere Service Advisor V5.2 AG Supports vehicles to 2018 2. With John Deere Service Advisor V5.2 CF Supports vehicles to 2018 3. With John Deere Service Advisor V5.2 CCE Supports vehicles to 2018 We will install the selected software in the lenovo T410 laptop, you can use it directly after receiving the package. Operating System: Windows XP 32 bit, Windows 7 32 bit, Windows 7 64 bit, Windows 8/8.1 32 bit, Windows 8/8.1 64 bit, Windows 10 32 bit, Windows 10 64 bit Multi-language available: English, French, Italian, Spanish, Portuguese Note: HDD comes in English in default. If you need other language, please contact our customer service before ordering. John Deere Service Advisor EDL (Electronic Data Link) heavy duty diagnostic adapter for construction equipment, agriculture, engines John Deere. Notice: If you want to do 3038E truck, then need to use V5.2 software (Hardisk Version). With
阅读全文